Published:
Work Analysis
How to Calculate Standard Time in Manufacturing

Standard time is a defined value that includes the net time corresponding to a set condition and method, plus the necessary buffer time.
This article explains the procedure and formula for setting standard time using the example of automobile component unit assembly, particularly with a net time of 60 seconds.
- Difference between observation time, net time, and standard time
- Five steps to set standard time
- 1. Fix target conditions and work methods
- 2. Divide elements and measure multiple times
- 3. Determine net time
- 4. Calculate standard time considering buffer time
- 5. Compare the set value with actual work and approve
- Calculation example for a net time of 60 seconds
- Three things often overlooked in calculations
- Simultaneous human and machine work
- Dual counting of auxiliary work, anomalies, and margins
- Confusion between standard time and takt time
- Frequently asked questions
- What percentage should the margin be?
- Can AI measure the work time directly as standard time?
- Summary: Align the definitions of net time and margin rate
- "Ollo Factory", a manufacturing-specific work analysis AI that automates time aggregation and comparison for standard time evaluation
- ① Organize observation time for elements
- ② Check cycles and differences among operators
- Watch Ollo Factory’s Work Comparison AI in Action
Difference between observation time, net time, and standard time
Terminology | Meaning in this article | Judgmental considerations |
|---|---|---|
Net time | Basic time that matches the standard condition and work pace | Do not treat simple average as the standard |
Buffer time | Time to be added as necessary | Clarify the target, basis, and denominator for calculation |
Standard time | Time set by reflecting net time and buffer time | Leave method, condition, and version |
Buffer time is the time needed to continue work, such as for recovery from fatigue or irregular accompanying tasks.JEED and the University of Occupational and Environmental Development: "Creation of Standard Time and Work Quantity Planning"The concepts of net time, buffer time, and work analysis are organized here.
Five steps to set standard time
Below, the five-step process from determining target conditions to measurement, calculation, and approval is explained. The correction coefficient and buffer rate should be determined according to the field setting standards.
1. Fix target conditions and work methods
Before measuring standard time, establish the following conditions.
Product and work conditions:Part number, component arrangement, jig, tools, inspection method
Personnel conditions:Number of personnel and skill and implementation conditions required for the task
Measurement range:From the start of jig setup to retrieving the inspection result
Averaging different cycles together can make it difficult to determine which task to apply the standard to.
2. Divide elements and measure multiple times
Divide sets, fastening, inspection confirmation, and retrieval. In addition to normal repetition, record when tool exchange or material replenishment occurs. Leave the cause of abnormal cycles and do not delete them silently.
3. Determine net time
There are methods for setting net time that involve time study with work pace evaluation or using established time data.
4. Calculate standard time considering buffer time
In this article, the buffer rate is defined as "buffer time ÷ net time". Once the buffer rate is known, standard time can be expressed as follows:
Standard time = Net time × (1 + buffer rate)
Also, if buffer time is known, standard time can be calculated as follows, even if buffer rate is not known:
Standard time = Net time + Buffer time
5. Compare the set value with actual work and approve
Confirm whether the necessary checks can be completed without interruption and whether the included buffer is not also included in other estimation items. The process manager approves the adopted value and application conditions, and re-evaluates when the configuration, equipment, or variety changes.
Calculation example for a net time of 60 seconds
Next, a calculation example with a net time of 60 seconds. Assume the work pace has been adjusted. Include cases where a margin is used and where the margin is known. These figures do not represent actual values or implementation effects.
Conditions | Calculation | Standard time |
|---|---|---|
10% margin | 60×(1+0.1) | 66 seconds |
6 seconds of margin | 60+6 | 66 seconds |
Actual data used for standard time evaluation can also be gathered and compared using Video Manual AI. The calculation rules and margin judgments follow the standards established on-site.
Three things often overlooked in calculations
Simultaneous human and machine work
When preparing the next component during automatic inspection, adding human work time and machine time together can double the cycle count. First determine whether you want to find the number of human units or the repeating time of the equipment, then verify overlaps on the time axis.
Dual counting of auxiliary work, anomalies, and margins
If the material supply time is allocated individually to the net time, adding the same supply to the margin time results in double counting. Sudden stops should not be processed uniformly with a standard margin rate; separate the standard time scope and the causes of improvement.
Confusion between standard time and takt time
Standard time is a setting for the work side. Takt time is the production time available for the period ÷ required production quantity. A mechanical shortening of the standard time method when demand changes is not possible.
Frequently asked questions
What percentage should the margin be?
A uniform optimal value cannot be shown. The margin is set based on fatigue, auxiliary work, on-site conditions, company standards, and measurement results. Keep the adoption rate, target work, and basis for setting.
Can AI measure the work time directly as standard time?
Measurement results are the basis for setting. Verify classification corrections, normal vs. abnormal distinction, work methods, rating, and margin handling, and the responsible person must adopt it as standard.
Summary: Align the definitions of net time and margin rate
Distinguish margin time, net time, and standard time, and define target conditions and work methods
Leave the basis for calculations and re-evaluate standard time when methods or equipment change
AI can streamline the organization of work data for standard time setting. Automate element work division, time aggregation, and cycle comparison, allowing the responsible person to focus on condition confirmation and standard setting.
"Ollo Factory", a manufacturing-specific work analysis AI that automates time aggregation and comparison for standard time evaluation
① Organize observation time for elements
Video can confirm element work and time for classification. Align where to measure from to where, using the video, and prepare materials for consistent handling of auxiliary work and anomalies.

Official demo screen of Ollo Factory. This is a different task from the unit assembly example in the text.
② Check cycles and differences among operators
Compare the same work and confirm time differences per element. Do not attribute differences solely to work pace; use them to investigate methods, equipment, and material supply conditions.

Official demo screen of Ollo Factory. This is a separate task from the unit assembly example in the text.
Automatically measured time is an observation value. A separate judgment is required to determine net time, rating, and denominator/rate for margin, and to approve it as standard.
Watch Ollo Factory’s Work Comparison AI in Action
About the author
K.Y. | Business Development Lead & Marketing, Ollo Inc.
K.Y. leads business development and marketing at Ollo Inc., an AI startup originating from the Matsuo Laboratory at the University of Tokyo and the developer of Ollo Factory, a work analysis AI for manufacturing.
After studying engineering and design at university, K.Y. joined a major automaker and worked on new electric-vehicle development, from design through factory production, including hands-on assembly-line training. K.Y. later worked in sales and marketing at a manufacturing startup.
Today, K.Y. helps manufacturing teams use AI to improve the way they work through Ollo Factory.
Back to articles
Related articles
See how Ollo Factory can support your factory
Book a demo
• See the product in action
• Discuss your production needs
• Explore available plans
Book a demo

Request a brochure
• Customer stories
• Key features
• How to get started

